2. This is ionic radii with a noble gas configuration.
这是稀有气体的离子半径。
youdao
3. Transitions or radii that are sharper than original design.
比初始设计更尖锐的过渡段或倒角。
youdao
4. Drag to add up to 4 concentric circles with adjustable radii.
拖动此形状，可添加多达4个具有可调半径的同心圆。
youdao
5. The cutting edge roundness can make chip curling radii larger.
切削刃钝圆一般能使切屑卷曲半径增大。
youdao
6. This is easily formed to the correct radii, tack weld both ends.
这是很容易形成正确的半径，钉焊接两端。
youdao
7. Not the radii but I will give you the diameters of these ball bearings.
不是半径，而是这些滚珠的直径。
youdao
8. British Armour Command Truck and Field Support Truck have their sight radii tuned.
英军装甲指挥卡车和战场支援卡车视野范围改动。
youdao
9. Use to estimate turning radii for a typical tractor with semitrailer and full trailer.
用于估计带有半挂车和全挂车的典型牵引车的转弯半径。
youdao
10. Railway transport equipment. cold folding radii for flat products. common requirements.
铁路运输设备。扁平轧材的冷弯半径。一般要求。
youdao
11. The radii of the rings are determined by the spacing of the gravity observation points.
圆的半径为重大观测点之间的距离所决定。
youdao
12. The radii of the rings are determined by the spacing of the gravity observation points .
圆的半径为重大观测点之间的距离所决定。
youdao
13. They get stuck at these radii, because if they go in either direction, they'll migrate right back.
它们就被堵住在这些半径上，因为如果它们走向任何一个方向，就会被拉回到原来的位置。
youdao
14. The results show that the depleted thickness is commensurate to the gyration radii of polymer molecule.
结果表明：衰竭层厚度与聚合物分子的回旋半径级别相当；
youdao
15. A new calculating model was derived from the relation of absolute hardness to the radii of polyvalent ions.
从绝对硬度与离子半径的关系导出一个高价离子电子亲合能的计算模型。
youdao
16. The influence of groove fillet radii of vertical rolls on cropping and margin deformation of slab were analyzed.
分析了立辊孔型内倒角半径对轧件切头尾量、轧件稳定段轧件边部变形程度的影响。
youdao
17. The boundary radii of excited atoms are defined by the classical turning point of the electron moving in an atom.
应用原子激发态中一个电子所受到的作用势，借助电子运动的经典转折点，定义原子激发态的边界半径。
youdao
18. Calculation method of 3g cell capacity and the characters of cell capacity and cell vesture radii are introduced.
介绍了3G小区容量的计算方法及小区容量和覆盖半径的特点。
youdao
19. The visibility, effective radii and liquid water path (LWP) of fog are the fundamental parameters for fog monitoring.
大雾区域地面能见度、垂直总水汽含量、雾滴有效半径等因子是对大雾进行有效监测的重要参数。
youdao
20. All this comes out of Doppler shift measurements: the velocities, the radii, the periods and even the masses of these objects.
顿移测量法得到，速度，半径：，周期，以及，这些物体的质量，如果作为观察者。
youdao
21. Radii stop converging as they approach the event horizon, are parallel at the horizon, and begin diverging in the interior.
当它们接近活动视界时候半径阻止了收缩，是与视界平行，而开始在内部分叉。
youdao
22. The loading dock and loading court off of Park road was designed to accommodate large turning radii required by semi-trucks.
设计将装载码头和装载庭院远离公园路是为了适应二轮半拖车大的转弯半径。
youdao
23. The cone radii are revised in response to length, creep and thickness of the belt, thereby increasing precision of cone drum curve.
并根据传动带的定长、打滑及厚度作了修正，从而提高了锥形轮曲线的精确度。
youdao
24. Data calculated by this method is exact, which show that the method is suit to the calculation of energy variation and critical radii.
根据这一计算方法能得到较为准确的数据，说明了本方法能较好地计算出水合物生成的能量变化和临界半径。
youdao
25. The major factors that affect the trapping were discussed and suitable beam waists and radii of the trapped particles were demonstrated.
给出影响捕获微粒的主要因素，指出存在最佳束腰半径和被捕获粒子半径。
youdao
26. A common formula for various types of rotors of different centrifugal radii on high speed centrifuges and ultracentrifuges were suggested.
本文提出了高速与超速离心机所用各类不同型号转子的离心半径的通用计算公式。
youdao
27. By constructing a metal cutting model using slip-line field theory, chip curling radii are predicted theoretically in orthogonal cutting processes.
通过采用滑移线场理论，建立了一种正交切削模型，使用这一模型，从理论上预测了切屑卷曲半径。
youdao
28. By constructing a metal cutting model using slip-line field theory, chip curling radii are predicted theoretically in orthogonal cutting processes.
通过采用滑移线场理论，建立了一种正交切削模型，使用这一模型，从理论上预测了切屑卷曲半径。
youdao
用作名词 (n.)
A plane figure bounded by two radii and the included arc of a circle. 由两个半径和两个半径中间的弧所形成的一个平面形状。
It is now necessary to introduce a sign convention for radii of curvature. 现在必须介绍曲率半径的正负号规则。
