3. Steering axis inclination is the inward tilt of the steeringknuckle at the top.
督导轴倾角是外来倾斜的转向节在最上方。
youdao
4. It was presented that a new precision forming technology of car steering knuckle in this paper.
文章提出了轿车转向节精密成形新工艺。
youdao
5. Situate the steering knuckle assembly so that it fits on to the cross member knuckle back plate.
位于该转向节大会，以便它适合于板的横梁关节回来。
youdao
6. Thus, the steeringknuckle, spindle, wheels, and tires turn to one side, causing the car to turn.
这样，转向节、转向节轴端、车轮和轮胎都会向一侧旋转，汽车实现转向。
youdao
7. The results show that the thermomechanical treatment can improve the quality of the automobile steering knuckle.
结果表明，锻造余热淬火工艺对汽车转向节质量有明显改善。
youdao
8. These include the fabrication of the Derailleur Cable Stop, and drilling the holes for both steeringknuckle levels.
这些措施包括停止生产的变速器电缆，钻两个孔，关节指导的水平。
youdao
9. The last modification required to the brake faceplate, is making the plate flush with the steering knuckle faceplate.
最后修改面板所需的制动，转向是使板与关节冲洗面板中删除。
youdao
10. A steering knuckle is the key component in cars, which needs high requirements in dimensional accuracy and product quality.
轿车转向节是轿车上的关键零件，对尺寸精度和产品质量要求很高。
youdao
11. This movement is produced by gearing and linkage between the steering wheel in front of the driver and the steeringknuckle.
这一运动是由装在驾驶员前面的转向盘与转向节之间的转向器和连杆装置来共同完成的。
youdao
12. The steeringknuckle then supported through Ball joints, by upper and lower control arms which are attached to the car frame.
转向节通过球头节与安装在车架上的上下控制臂相连。
youdao
13. By adjusting both tie rod-ends and steeringknuckle rod-ends, insure steering geometry has a neutral camber, and even toe-end.
通过调整这两个系杆结束，转向节杆结束，确保有一个中立的转向几何曲面，和甚至脚趾端。
youdao
14. Macro and micro structure of the fractured steering knuckle arm was examined by optical microscope and scanning electron microscope.
采用光学显微镜和扫描电镜对断裂转向节臂的宏、微观组织进行了分析。
youdao
15. This movement is produced by gearing and linkage between the steering wheel in front of the driver and the steering knuckle (or wheel).
这一运动是由装在驾驶员前面的转向盘与转向节(车轮)之间的转向器和连杆装置来共同完成的。
youdao
16. Assuming that the knuckle Face Plates have been fabricated (and welded to the frame), the steering knuckle assembly can now be assembled.
假设猪脚面板已制造(和焊接到框架)中，转向节大会，现在可以进行组装。
youdao
17. The trike frame should now be nearing completion and only requires the installation of the steeringknuckle mounting plates to be complete.
该三轮车框架现在应该已接近完成，只需要安装指导安装板的关节完整。
youdao
18. "Wuhu Zhongsheng Steering Knuckle Co. , Ltd. " is located in Wei 2 Road, Machinery & Industrial Zone of Wuhu County, Anhui province, China.
“芜湖中升汽车转向节制造有限公司”位于安徽省芜湖县机械工业园纬二路。
youdao
19. A feasible process scheme was made for forming the steering knuckle of a truck based on a technological analysis on the forging of the part.
通过对卡车转向节锻件的工艺分析，制定了合理的工艺方案。
youdao
20. The effect of thermomechanical treatment on the microstructure and properties of the automobile steering knuckle was researched in this paper.
研究了汽车转向节锻后余热淬火工艺对钢的组织和性能的影响。
youdao
21. Steering knuckle is a most important basic part of fanning truck, its used reliability is direct contact with running safety of human-vehicle.
转向节是农用运输车、汽车车桥的重要基础件，其使用是否可靠，直接危及人-车的行驶安全。
youdao
22. The production of domestic, import models of the steering section of the main pin, steering knuckle kingpin repair kit is more popular with users alike.
所生产的国产、进口车型的转向节主销、转向节主销修理包更受广大用户的一致好评。
youdao
23. It consists of steering wheel steering shaft worm gear sector pitman arm drag link steering knuckle arm king pin steering arms tie rod front axle and steeringknuckle.
24. It consists of steering wheel steering shaft worm gear sector pitman arm drag link steering knuckle arm king pin steering arms tie rod front axle and steering knuckle.
25. By improving the design of forging die and using press-forging and backward extrusion principle, solves the problems of 130 steering knuckle forming which can not be fully filled during forming.
